Local Inglis Appliance Repair Services

Inglis Washer Repair

Is your washer failing to spin or leaking on the laundry room floor? We handle everything from agitator issues to drive belt replacements, ensuring your Inglis washer handles your family’s toughest loads with ease once again.

Common Inglis Washing Machine Issues

• F0 E2: Over-Sudsing. Too much detergent or non-HE soap used. Fix: Run a “Rinse & Spin” cycle with no clothes. Use less soap next time.

• F5 E1: Lid Lock Fault. The lid isn’t locking or the sensor is broken. Fix: Check for detergent gunk in the latch. Ensure the lid strike (plastic tab) isn’t snapped.

• F7 E1: Motor Tachometer. The “brain” can’t tell if the drum is spinning. Fix: Check for a heavy rug or items stuck between the tubs. Could be a faulty speed sensor.

• F8 E1: Water Fill Fault. No water detected. Fix: Check that your hot/cold taps are on. Clean the small mesh screens in the water inlet valve.
• F9 E1: Long Drain. It took more than 10 mins to drain. Fix: Check the drain hose for kinks. Check the pump filter (if accessible) for coins or hairpins.
• sud / Sd: Suds Lock. Motor is struggling against bubbles. Fix: Leave the lid open and wait for bubbles to dissipate; run a drain cycle.

Inglis Dryer Repair

A dryer that won’t heat is a major inconvenience for any busy home. Our technicians quickly diagnose thermal fuses, heating elements, and rollers to restore that signature Inglis efficiency and get your clothes dry in a single cycle.

Common Inglis Dryer Issues

• AF: Airflow Issue. This is the most common Inglis call. Fix: Clean the lint screen and check the vent pipe leading outside. If the pipe is crushed or clogged, the dryer won’t heat.

• F01: Main Control Board. A logic failure. Fix: Unplug for 5 minutes to reset.

• F4 / E3: Thermal Sensor. The dryer thinks it’s overheating. Fix: Check for a lint blockage. The thermal fuse may have “blown” and will need replacement to get the heat back.

• L2: Low Voltage. The dryer is only getting half the power it needs (120v instead of 240v). Fix: Check your home’s circuit breaker—one of the two switches may have tripped.

Inglis Dishwasher Repair

If your dishes are coming out cloudy or the cycle won’t start, we can help. We specialize in Inglis filtration systems, spray arms, and drain pumps to ensure your cleanup is as simple and effective as it should be.

Common Inglis Dishwasher Issues

• 1-1 (One blink, pause, one blink): Control Board Error. Try a hard reset (flip the breaker).

• 6-1: Inlet Water. Not getting water. Check the float switch (the plastic mushroom in the corner) isn’t stuck “up.”

• 7-1: Heating Element. Water isn’t getting hot. The element at the bottom might be burnt out.

Inglis Fridge Repair

From top-freezer models to classic designs, we keep your groceries fresh. We provide expert repair for Inglis compressors, defrost timers, and thermostats to prevent food spoilage and keep your kitchen running smoothly.

Common Inglis Refrigerator Issues

Essential! If your Inglis fridge doesn’t have a screen, it will use a series of “beeps” or flashing interior lights to signal a fault.

• F1: RC (Fridge) Thermistor Fault. The refrigerator temperature sensor is failing. Fix: Replace the NTC sensor located on the side wall.

• F2: FC (Freezer) Thermistor Fault. The freezer temperature sensor is disconnected or broken. Fix: Check the wiring in the freezer; replace the sensor.

• F3 / F5: Evaporator Sensor Fault. The sensor that controls the defrost cycle is faulty. Fix: This often causes the fridge to stop cooling because the coils are blocked with ice.

• F6: Main Control Board Fault. A communication error in the “brain” of the fridge. Fix: Unplug for 5 minutes. If it returns, the board needs a swap.
• 7 (or “d”): Defrost Mode. Not an error! The fridge is currently melting ice off the coils. It should resume cooling in 20-30 minutes.

Inglis Stove & Cooktop Repair

Whether you have a gas or electric Inglis cooktop, safety and performance are our priorities. We repair faulty igniters, infinite switches, and heating coils so you can get back to stress-free meal prep.

Inglis Oven Repair

Uneven baking or a door that won’t seal properly can ruin a meal. We calibrate temperatures and replace faulty heating elements or sensors, restoring your Inglis oven to its original factory-set accuracy.

Common Inglis Range & Stove Issues

• F1: Control Board Failure. The clock/timer board is failing.

• F2: Oven Too Hot. Usually a stuck relay on the board. Fix: Unplug the stove immediately.

• F3 / F4: Oven Sensor. The thin metal rod inside the oven is broken. Fix: This is a simple DIY fix—two screws hold it in place.

• Loc / Child Lock: Not an error! Hold the “Clock” or “Cancel” button for 3-5 seconds to unlock the keypad.

The “Inglis Hidden Diagnostic” Mode

If your top-load washer is acting up but has no screen, you can often “talk” to it using the knob:

1. With the washer off/plugged in, turn the knob one full turn (360°) counter-clockwise.

2. Turn 3 clicks right, 1 click left, 1 click right.

3. All lights should flash. This is “Diagnostic Mode.” You can now turn the knob to see specific error codes stored in the memory.

The OEM Advantage: For every service listed above, we use only genuine Inglis components to protect your warranty, ensure a perfect fit, and maintain the long-lasting durability the Inglis brand is known for.